QSFP-DD - FIBERSTAMP https://www.fiberstamp.com Co-Packaged Optics (CPO) Fri, 12 Jun 2026 07:43:55 +0000 en-US hourly 1 https://wordpress.org/?v=7.0 https://www.fiberstamp.com/wp-content/uploads/2022/08/fiberstamp-logo-300-300-100x100.png QSFP-DD - FIBERSTAMP https://www.fiberstamp.com 32 32 FIBERSTAMP 200G QSFP DD xPSM8 20km Optical Transceiver(MPO16) https://www.fiberstamp.com/200g-qsfp-dd-xpsm8-20km.html https://www.fiberstamp.com/200g-qsfp-dd-xpsm8-20km.html#respond Wed, 10 Jun 2026 08:19:11 +0000 https://www.fiberstamp.com/?post_type=product&p=14939 The Fiberstamp Technologies FBL-200P8K20C is a Eight-Channel, Pluggable, Parallel, Fiber-Optic QSFP DD PSM8 for 2×100 Gigabit Ethernet , Infiniband DDR/EDR Applications. This transceiver is a high performance module for data communication and interconnect applications. It integrates eight data lanes in each direction with 208 Gbps bandwidth. Each lane can operate at 26Gbps up to 20km over G.652 SMF. These modules are designed to operate over single mode fiber systems using a nominal wavelength of 1310nm. The electrical interface uses a 76 contact edge type connector. The optical interface uses an 16 fiber MTP (MPO) connector. This module incorporates Fiberstamp Technologies proven circuit and Optical technology to provide reliable long life, high performance, and consistent service.

The post FIBERSTAMP 200G QSFP DD xPSM8 20km Optical Transceiver(MPO16) first appeared on FIBERSTAMP.

]]> Features
  • 8channels full-duplex transceiver modules
  • Supports8×25Gb/s aggregate bit rates
  • Supports8×10Gb/s aggregate bit rates if required
  • 8channels 1310nm DFB
  • 8channels PIN photo detector array
  • Internal CDR circuits on both receiver and transmitter channels
  • Support CDR bypass
  • Low power consumption <6.5W
  • Hot Pluggable QSFP DD form factor
  • Up to 20km reach for 652 SMF
  • Single male MPO16(APC 8-degree) connector receptacle
  • Operating case temperature 0°C to +70°C
  • 3Vpower supply voltage
  • RoHS compliant (lead free)

Applications

    • 2×100GEthernet links
    • Infiniband DDR/EDR
    • Datacenter and Enterprise networking

The post FIBERSTAMP 200G QSFP DD xPSM8 20km Optical Transceiver(MPO16) first appeared on FIBERSTAMP.

]]> https://www.fiberstamp.com/200g-qsfp-dd-xpsm8-20km.html/feed 0 400G QSFP56-DD to 4x100G QSFP28 MMF Active Optical Splitter Cable 8x50G PAM4 https://www.fiberstamp.com/400g-qsfp56-dd-to-4x100g-qsfp28-aoc.html https://www.fiberstamp.com/400g-qsfp56-dd-to-4x100g-qsfp28-aoc.html#respond Mon, 30 Mar 2026 09:39:21 +0000 https://www.fiberstamp.com/?post_type=product&p=14848 FIBERSTAMP’s FYHG-400MXXXC MMF Active Optical Splitter Cable is used in 4 X 100 Gigabit Ethernet links over OM3/OM4/OM5 multimode fiber, which provides connectivity between system units with a 400GbE connector on one side and four separate 100GbE connectors on the other four sides. The cable connects data signals from each of the 8 MMF (Multi Mode Fiber) pairs on the single QSFP56-DD end to the dual pair of each of the QSFP56 multiport ends.

FIBERSTAMP’s FYHG-400MXXXC MMF Active Optical Splitter Cable is compliant with the QSFP-DD-MSA and with 100GBASE-SR2 specification. Digital diagnostics functions are available via the I2C interface as specified by CMIS V4.0. The transceiver is RoHS 2.0 compliant and lead-free per Directive 2011/65/EU.

The post 400G QSFP56-DD to 4x100G QSFP28 MMF Active Optical Splitter Cable 8x50G PAM4 first appeared on FIBERSTAMP.

]]> Features

  • Hot-plug QSFP56-DD and QSFP28form factor
  • QSFP28 Electrical interface supports 4x 25G NRZ or 2X 50G PAM4
  • Host RS-FEC needs OFF When QSFP56Electrical interface is 4x25G NRZ
  • 8x 50Gb/s PAM4 modulation
  • Low power dissipation <9W (400G End)
  • Low power dissipation <4.5W (100G End)
  • RoHS-6 compliant (lead-free)
  • Commercial case temperature range of 0°C to 70°C
  • Single 3.3V power supply
  • Maximum link length of 70m on OM3 MMF
    and 100m on OM4 & OM5 MMF
  • Uncooled 850nm VCSEL array (both End)
  • PIN photo detector array (both End)
  • 400GBASE-SR8 and 100GBASE-SR2 compliant
  • I2C management interface
  • CMIS V4.0 compliant

 

Applications

  • IEEE 802.3cd&nbsp100GBASE-SR2 Ethernet (PAM4)
  • IEEE 802.3cd&nbsp400GBASE-SR8 Ethernet (PAM4)

The post 400G QSFP56-DD to 4x100G QSFP28 MMF Active Optical Splitter Cable 8x50G PAM4 first appeared on FIBERSTAMP.

]]> https://www.fiberstamp.com/400g-qsfp56-dd-to-4x100g-qsfp28-aoc.html/feed 0 FIBERSTAMP 400G QSFP-DD to 400G OSFP-RHS AOC Optical Transceiver Module https://www.fiberstamp.com/400g-qsfp-dd-400g-osfp-rhs.html https://www.fiberstamp.com/400g-qsfp-dd-400g-osfp-rhs.html#respond Fri, 27 Mar 2026 09:17:44 +0000 https://www.fiberstamp.com/?post_type=product&p=14837 FIBERSTAMP’s FYLU-400M50C MMF Active Optical Cable is used in 4 X 100Gigabit Ethernet links over OM3/OM4 multimode fiber. The OSFP-RHS port has integrate 4 independent transmit and receive channels, each capable of 106.25Gb/s PAM4 operation for an aggregate data rate of 425Gb/s, while the QSFP-DD port has integrate 4 independent transmit and receive channels and uses QSFP-DD MSA，which provides increased port density and total system cost savings for switches and routers, etc. It is compliant with IEEE 802.3db, IEEE 802.3ck and OSFP&QSFP-DD MSA.

The post FIBERSTAMP 400G QSFP-DD to 400G OSFP-RHS AOC Optical Transceiver Module first appeared on FIBERSTAMP.

]]> Features

  • Hot-plug OSFP-RHS and QSFPDD form factor
  • Transmission data rate up to 106.25G per channel
  • 25Gbps PAM4 transmitter and PAM4 receiver
  • 4 channels 850nm VCSEL array(both End)
  • 4 channels PIN photo detector array(both End)
  • Power consumption <8W
  • Compliant to OSFP&QSFP-DD MSA and CMIS4.0
  • Maximum link length of 30m on OM3 Multimode Fiber (MMF)and 50m on OM4 MMF with FEC
  • Built-in digital diagnostic functions
  • Operating case temperature 10°C to +70°C
  • 3V power supply voltage
  • RoHS compliant(lead free)

 

Applications

  • IEEE 802.3db&nbsp400GBASE-VR4 Ethernet (PAM4)
  • The transceiver is designed for Ethernet, Telecom and Infiniband use cases.

The post FIBERSTAMP 400G QSFP-DD to 400G OSFP-RHS AOC Optical Transceiver Module first appeared on FIBERSTAMP.

]]> https://www.fiberstamp.com/400g-qsfp-dd-400g-osfp-rhs.html/feed 0 FIBERSTAMP Color X 400G QSFP-DD PSM4 DWDM4 https://www.fiberstamp.com/product/color-x-400g-qsfp-dd-dwdm4 https://www.fiberstamp.com/product/color-x-400g-qsfp-dd-dwdm4#respond Tue, 03 Feb 2026 06:59:13 +0000 https://www.fiberstamp.com/?post_type=product&p=14633 The Color X 400G QSFP-DD PSM4 DWDM4 is built on 4×100G PAM4 silicon photonic MZ modulation technology, enabling high-capacity DWDM transmission in compact form factors. It supports DWDM O-BAND with 200GHz spacing across 33 channels, delivering transmission distances of up to 10km, and up to 30km when used with an external SOA. The module is equipped with an MPO connector, making it well suited for high-density data center and metro interconnect applications.

The post FIBERSTAMP Color X 400G QSFP-DD PSM4 DWDM4 first appeared on FIBERSTAMP.

]]>
  • 4×100G PAM4 silicon photonic MZ modulation
  • DWDM O-BAND, 200GHz spacing, 33 channels
  • Transmission reach: up to 10km (30km with external SOA)
  • QSFP-DD form factor
  • MPO optical connector

    • The post FIBERSTAMP Color X 400G QSFP-DD PSM4 DWDM4 first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/product/color-x-400g-qsfp-dd-dwdm4/feed 0     FIBERSTAMP 800G QSFP-DD to 2x400G QSFP112 Active Copper Cable ACC https://www.fiberstamp.com/800g-qsfp-dd-to-2x400g-qsfp112-acc.html https://www.fiberstamp.com/800g-qsfp-dd-to-2x400g-qsfp112-acc.html#respond Sat, 11 Oct 2025 10:11:28 +0000 https://www.fiberstamp.com/?post_type=product&p=13852 FIBERSTAMP’s ACC(Active Copper Cable) assembly series product provide superior signal integrity performance and reliability, comparing to PCC and AOC, ACC is a re-drive solution which built-in linear equalizer to compensate transmission loss, it is an effective solution with low power, low latency, low cost to help high-speed data centers even AI high-computational applications.

    FIBERSTAMP’s FZL2J-800XXM05C cable connects data signals from each of the 16 pairs on the single QSFP-DD end to the dual QSFP112 ends, each pair operates at data rates of up to 100Gb/s and can be adaptive downward compatibility. The product operates 3.3V power supply and comply with QSFP-DD MSA and IEEE802.3ck ,it’s high performance & cost effective I/O solutions for LAN, HPC and SAN.

    The post FIBERSTAMP 800G QSFP-DD to 2x400G QSFP112 Active Copper Cable ACC first appeared on FIBERSTAMP.

    ]]>     Features

    • Hot-plug QSFP-DD&QSFP112 form factor
    • Support 8x 50/100Gb/s PAM4 modulation with 16 pairs
    • Support up to 5m length
    • 100 ohm differential impedance system
    • 3V power supply & typical power consumption 2.5W
    • Commercial case temperature range of 0°C to 70°C
    • I2C management

    Applications

    • Infiniband NDR/HDR/EDR
    • Switch / router / HBA
    • Enterprise network
    • Data Center Network
    • Data storage and communication industry

    STANDARDS COMPLIANCE

    • IEEE P802.3ck D3.0
    • QSFP-DD/QSFP112 MSA HW Rev 6.01
    • CMIS 4.0
    • RoHS

    The post FIBERSTAMP 800G QSFP-DD to 2x400G QSFP112 Active Copper Cable ACC first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/800g-qsfp-dd-to-2x400g-qsfp112-acc.html/feed 0     800G QSFP-DD to 4x200G QSFP112 Active Copper Cable ACC https://www.fiberstamp.com/800g-qsfp-dd-to-4x200g-qsfp112-acc.html https://www.fiberstamp.com/800g-qsfp-dd-to-4x200g-qsfp112-acc.html#respond Sat, 11 Oct 2025 09:58:50 +0000 https://www.fiberstamp.com/?post_type=product&p=13848 FIBERSTAMP’s ACC(Active Copper Cable) assembly series product provide superior signal integrity performance and reliability, comparing to PCC and AOC, ACC is a re-drive solution which built-in linear equalizer to compensate transmission loss, it is an effective solution with low power, low latency, low cost to help high-speed data centers even AI high-computational applications.

    FIBERSTAMP’s FZL4J-800XXM05C cable assemblies are effective alternatives to fiber optics. The cable connects data signals from each of the 16 pairs on the single QSFP-DD end to the quad QSFP112 ends, each pair operates at data rates of up to 100Gb/s, each QSFP-DD/QSFP112 port can be addressed by EEPROM to provide product information, which can be read or write by I2C interface, it’s a high performance & cost effective I/O solutions for LAN, HPC and SAN.

    The post 800G QSFP-DD to 4x200G QSFP112 Active Copper Cable ACC first appeared on FIBERSTAMP.

    ]]>     Features

    • Hot-plug QSFP-DD and QSFP112 form factor
    • Support 8x 50/100Gb/s PAM4 modulation with 16 pairs
    • Support up to 5m length
    • 100 ohm differential impedance system
    • 3V power supply & typical power consumption 3.5W
    • Commercial case temperature range of 0°C to 70°C
    • I2C management

    Applications

    • Infiniband NDR/HDR/EDR
    • Switch / router / HBA
    • Enterprise network
    • Data Center Network
    • Data storage and communication industry

    STANDARDS COMPLIANCE

    • IEEE P802.3ck D3.0
    • QSFP-DD/QSFP112 MSA HW Rev 6.01
    • CMIS 4.0
    • RoHS

     

    The post 800G QSFP-DD to 4x200G QSFP112 Active Copper Cable ACC first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/800g-qsfp-dd-to-4x200g-qsfp112-acc.html/feed 0     FIBERSTAMP 400G QSFP-DD ER8 40km Optical Transceiver Module https://www.fiberstamp.com/400g-qsfpdd-er8.html https://www.fiberstamp.com/400g-qsfpdd-er8.html#respond Thu, 18 Sep 2025 09:24:25 +0000 https://www.fiberstamp.com/?post_type=product&p=13829 FIBERSTAMP's 400G QSFP-DD ER8 module is designed for 40 km optical communication applications, and it is compliant to IEEE 802.3bs for 400GE Ethernet. This module contains 8-lane optical transmitter, 8-lane optical receiver and module management block including 2 wire serial interfaces. The optical signals are multiplexed to a single-mode fiber through an industry standard LC connector.

    The post FIBERSTAMP 400G QSFP-DD ER8 40km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>     Features

    • QSFP-DD MSA compliant
    • Compliant to IEEE 802.3bs 400GBASE-ER8
    • Digital diagnostic monitoring support
    • Hot pluggable 76 pin electrical interface
    • 8 LAN-WDM lanes MUX/DEMUX design
    • 53.125 Gbps PAM4 Channel Electrical Serial
    • Interface (400GAUI-8)
    • Maximum power consumption 15.4 W
    • LC duplex connector
    • Supports 425 Gb ps bit rate
    • Up to 40 km transmission on single mode fiber
    • Operating case temperature: 0 。C to 70 。C
    • Single 3.3 V power supply
    • RoHS 2 compliant

    Applications

    • 400GBASE-ER8 Ethernet
    • Telecom networking
    • Data Center Interconnect

    The post FIBERSTAMP 400G QSFP-DD ER8 40km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/400g-qsfpdd-er8.html/feed 0     FIBERSTAMP 200G QSFP-DD ER4 40km Optical Transceiver Module https://www.fiberstamp.com/200g-qsfpdd-er4.html https://www.fiberstamp.com/200g-qsfpdd-er4.html#respond Thu, 18 Sep 2025 09:17:56 +0000 https://www.fiberstamp.com/?post_type=product&p=13826 FIBERSTAMP’s 200GE QSFP-DD ER4 Optical Transceiver modules are designed for using in 200Gigabit Ethernet 40km links over SMF single-mode fiber. They are compliant with the QSFP-DD MSA and with IEEE 802.3cn 200GBASE-ER4 specification. Digital diagnostics functions are available via the I2C interface as specified by CMIS V4.0. These modules can convert 8 channels of 25Gbps (NRZ) electrical input data to 4 channels of 50Gbps (PAM4) optical signal, and also can convert 4 channels of 50Gbps (PAM4) optical signal to 8 channels of 25Gbps (NRZ) electrical output data. And these modules incorporate FIBERSTAMP Technologies proven circuit and EML technology to provide reliable long life, high performance, and consistent service.

    The post FIBERSTAMP 200G QSFP-DD ER4 40km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>
  • Features
    • 125Gbps(26.5625GBd) PAM4 LWDM optics architecture
    • 78125 or 26.5625GbpsElectrical Interface (200GAUI-8)
    • 4x53Gbps PAM4 optical transmitter and receiver
    • 4 channels LWDMcooled EML transmitter
    • 4 channels APD receiver
    • Internal 8:4 Gearbox DSP with KP FEC (optional)
    • Power consumption <9W
    • Hot Pluggable QSFP DD form factor and Compliant with CMIS 4.0
    • Up to 40km transmission over G.652 SMF
    • Duplex LC connector receptacle
    • Built-in digital diagnostic functions
    • Operating case temperature from 0°C to +70°C
    • 3V power supply voltage
    • RoHS compliant (lead free)

     

    Applications

    • 200GBASE-ER4 Ethernet
    • Telecom networking
    • Datacenter

    • The post FIBERSTAMP 200G QSFP-DD ER4 40km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/200g-qsfpdd-er4.html/feed 0     FIBERSTAMP 200G QSFP-DD LR4 LWDM 10km Optical Transceiver Module https://www.fiberstamp.com/200g-qsfpdd-lr4.html https://www.fiberstamp.com/200g-qsfpdd-lr4.html#respond Thu, 18 Sep 2025 08:16:01 +0000 https://www.fiberstamp.com/?post_type=product&p=13823 FIBERSTAMP’s 200G QSFP-DD LR4 Optical Transceiver modules are designed for using in 200Gigabit Ethernet 10km links over SMF single-mode fiber. They are compliant with the QSFP-DD MSA and with IEEE 802.3cn 200GBASE-LR4 specification. Digital diagnostics functions are available via the I2C interface as specified by CMIS V4.0. These modules can convert 8 channels of 25Gbps (NRZ) electrical input data to 4 channels of 50Gbps (PAM4) optical signal, and also can convert 4 channels of 50Gbps (PAM4) optical signal to 8 channels of 25Gbps (NRZ) electrical output data. And these modules incorporate FIBERSTAMP Technologies proven circuit and EML technology to provide reliable long life, high performance, and consistent service.

    The post FIBERSTAMP 200G QSFP-DD LR4 LWDM 10km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>
  • Features
    • 125Gbps(26.5625GBd) PAM4 LWDM optics architecture
    • 78125 or 26.5625GbpsElectrical Interface (200GAUI-8)
    • 4x53Gbps PAM4 optical transmitter and receiver
    • 4 channels LWDM cooled EML transmitter
    • 4 channels PIN photo detector array receiver
    • Internal 8:4 Gearbox DSP with KP FEC (optional)
    • Power consumption <9W
    • Hot Pluggable QSFP DD form factor and Compliant with CMIS 4.0
    • Up to 10km transmission over G.652 SMF
    • Duplex LC connector receptacle
    • Built-in digital diagnostic functions
    • Operating case temperature from 0°C to +70°C
    • 3V power supply voltage
    • RoHS compliant (lead free)

     

    Applications

    • 200GBASE-LR4 Ethernet
    • Datacenter

    • The post FIBERSTAMP 200G QSFP-DD LR4 LWDM 10km Optical Transceiver Module first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/200g-qsfpdd-lr4.html/feed 0     200G QSFP-DD to 2XQSFP28 DAC https://www.fiberstamp.com/200g-qsfp-dd-to-2xqsfp28-dac.html https://www.fiberstamp.com/200g-qsfp-dd-to-2xqsfp28-dac.html#respond Wed, 16 Jul 2025 09:52:14 +0000 https://www.fiberstamp.com/?post_type=product&p=13630 FIBERSTAMP’s FWL-E25200XXC cable assembly is a customized passive copper cable. The cable connects data signals from each of the 16 pairs on the single QSFP-DD end to the dual QSFP28 end, the 16 pairs operates at data rates of up to 25Gb/s, each end can be addressed by EEPROM to provide product information, which can be read or write by I2C interface.

    The post 200G QSFP-DD to 2XQSFP28 DAC first appeared on FIBERSTAMP.

    ]]>     Features

    • Hot-plug QSFP-DD and QSFP28 form factor
    • Support 8x 25Gb/s NRZ modulation
    • Commercial case temperature range of 0°C to 70°C
    • 26 AWG ~30 AWG support up to 5m length
    • I2C management interface
    • RoHS compliant

    Applications

    • Data storage and communication industry
    • Switch / router / HBA
    • Enterprise network
    • SAN
    • Data Center Network

    STANDARDS COMPLIANCE

    • IEEE802.3bj
    • QSFP/QSFP-DD MSA

    The post 200G QSFP-DD to 2XQSFP28 DAC first appeared on FIBERSTAMP.

    ]]>     https://www.fiberstamp.com/200g-qsfp-dd-to-2xqsfp28-dac.html/feed 0